 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM Rev. 05 -- 17 December 2004 Product data 1. General description The P89LPC906/907/908 are single-chip microcontrollers in low-cost 8-pin packages, based on a high performance processor architecture that executes instructions in two to four clocks, six times the rate of standard 80C51 devices. Many system-level functions have been incorporated into the P89LPC906/907/908 in order to reduce component count, board space, and system cost. 2. Features 2.1 Principal features s 1 kB byte-erasable Flash code memory organized into 256-byte sectors and 16-byte pages. Single-byte erasing allows any byte(s) to be used as non-volatile data storage. s 128-byte RAM data memory. s Two 16-bit counter/timers. (Timer 0 may be configured to toggle a port output upon timer overflow or to become a PWM output on the P89LPC907 device). s 23-bit system timer that can also be used as a Real-Time clock. s A single analog comparator with selectable reference source. s Enhanced UART with fractional baudrate generator, break detect, framing error detection, automatic address detection and versatile interrupt capabilities (P89LPC908, transmit only on P89LPC907). s Internal RC oscillator option (factory calibrated to 1 %) allows operation without external oscillator components. The RC oscillator option is selectable and fine tunable. s 2.4 V to 3.6 V VDD operating range with 5 V tolerant I/O pins (may be pulled up or driven to 5.5 V). Supply pins located at package centers for improved supply decoupling and reduced EMI. s Up to six I/O pins when using internal oscillator and reset options. s 8-pin SO-8 package. 2.2 Additional features s A high performance 80C51 CPU provides instruction cycle times of 111 ns to 222 ns for all instructions except multiply and divide when executing at 18 MHz (P89LPC906) (167 ns to 333 ns at 12 MHz). This is six times the performance of the standard 80C51 running at the same clock frequency. A lower clock frequency for the same performance results in power savings and reduced EMI. s In-Application Programming (IAP-Lite) and byte erase allows code memory to be used for non-volatile data storage. Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core s Serial Flash In-Circuit Programming (ICP) allows simple production coding with commercial EPROM programmers. Flash security bits prevent reading of sensitive application programs. s Watchdog timer with separate on-chip oscillator, requiring no external components. The watchdog prescaler is selectable from 8 values. s Low voltage reset (Brownout detect) allows a graceful system shutdown when power fails. May optionally be configured as an interrupt. s Idle and two different Power-down reduced power modes. Improved wake-up from Power-down mode (a low interrupt input starts execution). Typical Power-down current is 1 A (total Power-down with voltage comparators disabled). s Active-LOW reset. On-chip power-on reset allows operation without external reset components. A reset counter and reset glitch suppression circuitry prevent spurious and incomplete resets. A software reset function is also available. s Configurable on-chip oscillator with frequency range options selected by user programmed Flash configuration bits. Oscillator options support frequencies from 20 kHz to the maximum operating frequency of 18 MHz (P89LPC906). s Programmable port output configuration options: quasi-bidirectional, open drain, push-pull, input-only. s Port `input pattern match' detect. Port 0 may generate an interrupt when the value of the pins match or do not match a programmable pattern. s LED drive capability (20 mA) on all port pins. A maximum limit is specified for the entire chip. s Controlled slew rate port outputs to reduce EMI. Outputs have approximately 10 ns minimum ramp times. s Only power and ground connections are required to operate the P89LPC906/907/908 when internal reset option is selected. s Four interrupt priority levels. s Three keypad interrupt inputs. s Second data pointer. s Schmitt trigger port inputs. s Emulation support. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 2 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 3. Ordering information Table 1: Ordering information Package Name P89LPC906FD P89LPC907FD P89LPC908FD SO8 Description plastic small outline package; 8 leads; body width 7.5 mm Version SOT96-1 Type number 3.1 Ordering options Table 2: Part options Temperature range -40 C to +85 C Frequency 0 MHz to 18 MHz Internal RC or watchdog Internal RC or watchdog Type number P89LPC906FD P89LPC907FD P89LPC908FD 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 3 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 4. Block diagram P89LPC906 HIGH PERFORMANCE ACCELERATED 2-CLOCK 80C51 CPU 1 kB CODE FLASH 128-BYTE DATA RAM PORT 3 CONFIGURABLE I/Os PORT 1 INPUT INTERNAL BUS TIMER 0 TIMER 1 REAL-TIME CLOCK/ SYSTEM TIMER ANALOG COMPARATOR PORT 0 CONFIGURABLE I/Os KEYPAD INTERRUPT WATCHDOG TIMER AND OSCILLATOR PROGRAMMABLE OSCILLATOR DIVIDER CPU CLOCK POWER MONITOR (POWER-ON RESET, BROWNOUT RESET) CRYSTAL OR RESONATOR CONFIGURABLE OSCILLATOR ON-CHIP RC OSCILLATOR 002aaa460 Fig 1. P89LPC906 block diagram. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 4 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core P89LPC907 HIGH PERFORMANCE ACCELERATED 2-CLOCK 80C51 CPU 1 kB CODE FLASH 128-BYTE DATA RAM PORT 1 CONFIGURABLE I/O INTERNAL BUS UART TIMER 0 TIMER 1 REAL-TIME CLOCK/ SYSTEM TIMER PORT 0 CONFIGURABLE I/Os ANALOG COMPARATOR KEYPAD INTERRUPT WATCHDOG TIMER AND OSCILLATOR PROGRAMMABLE OSCILLATOR DIVIDER CPU CLOCK POWER MONITOR (POWER-ON RESET, BROWNOUT RESET) ON-CHIP RC OSCILLATOR 002aaa461 Fig 2. P89LPC907 block diagram. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 5 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core P89LPC908 HIGH PERFORMANCE ACCELERATED 2-CLOCK 80C51 CPU 1 kB CODE FLASH 128-BYTE DATA RAM PORT 1 CONFIGURABLE I/Os INTERNAL BUS UART TIMER 0 TIMER 1 REAL-TIME CLOCK/ SYSTEM TIMER PORT 0 CONFIGURABLE I/Os ANALOG COMPARATOR KEYPAD INTERRUPT WATCHDOG TIMER AND OSCILLATOR PROGRAMMABLE OSCILLATOR DIVIDER CPU CLOCK POWER MONITOR (POWER-ON RESET, BROWNOUT RESET) ON-CHIP RC OSCILLATOR 002aaa462 Fig 3. P89LPC908 block diagram. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 6 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 5. Pinning information 5.1 Pinning handbook, halfpage RST/P1.5 1 VSS 2 P0.6/CMP1/KBI6 3 XTAL1/P3.1 4 8 P0.4/CIN1A/KBI4 P0.5/CMPREF/KBI5 VDD CLKOUT/XTAL2/P3.0 P89LPC906 7 6 5 002aaa454 Fig 4. P89LPC906 pinning. handbook, halfpage RST/P1.5 1 VSS 2 P0.6/CMP1/KBI6 3 P1.2/T0 4 8 P0.4/CIN1A/KBI4 P0.5/CMPREF/KBI5 VDD P1.0/TxD P89LPC907 7 6 5 002aaa455 Fig 5. P89LPC907 pinning. handbook, halfpage RST/P1.5 1 VSS 2 P0.6/CMP1/KBI6 3 P1.1/RxD 4 8 P0.4/CIN1A/KBI4 P0.5/CMPREF/KBI5 VDD P1.0/TxD P89LPC908 7 6 5 002aaa456 Fig 6. P89LPC908 pinning. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 7 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 5.2 Pin description Table 3: Symbol P0.4 to P0.6 P89LPC906 pin description Pin Type I/O Description Port 0: Port 0 is an I/O port with a user-configurable output types. During reset Port 0 latches are configured in the input only mode with the internal pull-up disabled. The operation of Port 0 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to Section 8.11.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. The Keypad Interrupt feature operates with Port 0 pins. All pins have Schmitt triggered inputs. Port 0 also provides various special functions as described below: 8 I/O I I 7 I/O I I 3 I/O O I P1.5 1 I I P0.4 -- Port 0 bit 4. CIN1A -- Comparator positive input. KBI4 -- Keyboard input 4. P0.5 -- Port 0 bit 5. CMPREF -- Comparator reference (negative) input. KBI5 -- Keyboard input 5. P0.6 -- Port 0 bit 6. CMP1 -- Comparator 1 output. KBI6 -- Keyboard input 6. P1.5 -- Port 1 bit 5 (input only). RST -- External Reset input during Power-on or if selected via UCFG1. When functioning as a reset input a LOW on this pin resets the microcontroller, causing I/O ports and peripherals to take on their default states, and the processor begins execution at address 0. Also used during a power-on sequence to force In-System Programming mode. When using an oscillator frequency above 12 MHz, the reset input function of P1.5 must be enabled. An external circuit is required to hold the device in reset at power-up until VDD has reached its specified level. When system power is removed VDD will fall below the minimum specified operating voltage. When using an oscillator frequency above 12 MHz, in some applications, an external brownout detect circuit may be required to hold the device in reset when VDD falls below the minimum specified operating voltage. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 8 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core Table 3: Symbol P89LPC906 pin description...continued Pin Type I/O Description Port 3: Port 3 is an I/O port with a user-configurable output types. During reset Port 3 latches are configured in the input only mode with the internal pull-up disabled. The operation of port 3 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to Section 8.11.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. All pins have Schmitt triggered inputs. Port 3 also provides various special functions as described below: 5 I/O O O P3.0 -- Port 3 bit 0. XTAL2 -- Output from the oscillator amplifier (when a crystal oscillator option is selected via the FLASH configuration). CLKOUT -- CPU clock divided by 2 when enabled via SFR bit (ENCLK to TRIM.6). It can be used if the CPU clock is the internal RC oscillator, Watchdog oscillator or external clock input, except when XTAL1/XTAL2 are used to generate clock source for the real time clock/system timer. P3.1 -- Port 3 bit 1. XTAL1 -- Input to the oscillator circuit and internal clock generator circuits (when selected via the FLASH configuration). It can be a port pin if internal RC oscillator or Watchdog oscillator is used as the CPU clock source, and if XTAL1/XTAL2 are not used to generate the clock for the real time clock/system timer. Ground: 0 V reference. Power Supply: This is the power supply voltage for normal operation as well as Idle and Power-down modes. P3.0 to P3.1 4 I/O I VSS VDD 2 6 I I Table 4: Symbol P89LPC907 pin description Pin Type I/O Description Port 0: Port 0 is an I/O port with a user-configurable output type. During reset Port 0 latches are configured in the input only mode with the internal pull-up disabled. The operation of Port 0 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to Section 8.11.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. The Keypad Interrupt feature operates with Port 0 pins. All pins have Schmitt triggered inputs. Port 0 also provides various special functions as described below: 8 I/O I I 7 I/O I I 3 I/O O I P0.4 -- Port 0 bit 4. CIN1A -- Comparator positive input. KBI4 -- Keyboard input 4. P0.5 -- Port 0 bit 5. CMPREF -- Comparator reference (negative) input. KBI5 -- Keyboard input 5. P0.6 -- Port 0 bit 6. CMP1 -- Comparator 1 output. KBI6 -- Keyboard input 6. P0.4 to P0.6 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 9 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core Table 4: Symbol P89LPC907 pin description...continued Pin Type Description Port 1: Port 1 is an I/O port with a user-configurable output types. During reset Port 1 latches are configured in the input only mode with the internal pull-up disabled. The operation of the configurable Port 1 pins as inputs and outputs depends upon the port configuration selected. Each of the configurable port pins are programmed independently. Refer to Section 8.11.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. P1.5 is input only. All pins have Schmitt triggered inputs. Port 1 also provides various special functions as described below: 5 4 1 I/O O I/O I/O I I P1.0 -- Port 1 bit 0. TxD -- Serial port transmitter data. P1.2 -- Port 1 bit 0. T0 -- Timer 0 external clock input, toggle output, PWM output. P1.5 -- Port 1 bit 5 (input only). RST -- External Reset input during Power-on or if selected via UCFG1. When functioning as a reset input a LOW on this pin resets the microcontroller, causing I/O ports and peripherals to take on their default states, and the processor begins execution at address 0. Also used during a power-on sequence to force In-System Programming mode. Ground: 0 V reference. Power Supply: This is the power supply voltage for normal operation as well as Idle and Power-down modes. P1.0 to P1.5 VSS VDD 2 6 I I Table 5: Symbol P89LPC908 pin description Pin Type I/O Description Port 0: Port 0 is an I/O port with a user-configurable output types. During reset Port 0 latches are configured in the input only mode with the internal pull-up disabled. The operation of Port 0 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to Section 8.11.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. The Keypad Interrupt feature operates with Port 0 pins. All pins have Schmitt triggered inputs. Port 0 also provides various special functions as described below: 8 I/O I I 7 I/O I I 3 I/O O I P0.4 -- Port 0 bit 4. CIN1A -- Comparator positive input. KBI4 -- Keyboard input 4. P0.5 -- Port 0 bit 5. CMPREF -- Comparator reference (negative) input. KBI5 -- Keyboard input 5. P0.6 -- Port 0 bit 6. CMP1 -- Comparator 1 output. KBI6 -- Keyboard input 6. P0.4 to P0.6 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 10 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core Table 5: Symbol P89LPC908 pin description...continued Pin Type Description Port 1: Port 1 is an I/O port with a user-configurable output types. During reset Port 1 latches are configured in the input only mode with the internal pull-up disabled. The operation of the configurable Port 1 pins as inputs and outputs depends upon the port configuration selected. Each of the configurable port pins are programmed independently. Refer to Section 8.11.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. P1.5 is input only. All pins have Schmitt triggered inputs. Port 1 also provides various special functions as described below: 5 4 1 I/O O I/O I I I P1.0 -- Port 1 bit 0. TxD -- Serial port transmitter data. P1.1 -- Port 1 bit 1. RxD -- Serial port receiver data. P1.5 -- Port 1 bit 5 (input only). RST -- External Reset input during Power-on or if selected via UCFG1. When functioning as a reset input a LOW on this pin resets the microcontroller, causing I/O ports and peripherals to take on their default states, and the processor begins execution at address 0. Also used during a power-on sequence to force In-System Programming mode. Ground: 0 V reference. Power Supply: This is the power supply voltage for normal operation as well as Idle and Power-down modes. P1.0 to P1.5 VSS VDD 2 6 I I 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 11 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 6. Logic symbols VDD VSS PORT 1 PORT 0 CLKOUT XTAL2 XTAL1 PORT 3 Fig 7. P89LPC906 logic symbol. VDD PORT 1 PORT 0 Fig 8. P89LPC907 logic symbol. VDD P89LPC907 KBI4 KBI5 KBI6 CIN1A CMPREF CMP1 P89LPC906 KBI4 KBI5 KBI6 CIN1A CMPREF CMP1 RST 002aaa457 VSS RST T0 TxD 002aaa458 VSS PORT 1 PORT 0 Fig 9. P89LPC908 logic symbol. P89LPC908 KBI4 KBI5 KBI6 CIN1A CMPREF CMP1 RST RxD TxD 002aaa459 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 12 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core Table 6 highlights the differences between these three devices. For a complete list of device features, please see Section 2 "Features" on page 1. Table 6: Product comparison overview External CLKOUT crystal pins output X X T0 PWM output X Analog comparator X X X UART TxD X X Rxd X Type number P89LPC906FD P89LPC907FD P89LPC908FD 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 13 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 7. Special function registers Remark: Special Function Registers (SFRs) accesses are restricted in the following ways: * User must not attempt to access any SFR locations not defined. * Accesses to any defined SFR locations must be strictly for the functions for the SFRs. * SFR bits labeled `-', `0' or `1' can only be written and read as follows: - `-' Unless otherwise specified, must be written with `0', but can return any value when read (even if it was written with `0'). It is a reserved bit and may be used in future derivatives. - `0' must be written with `0', and will return a `0' when read. - `1' must be written with `1', and will return a `1' when read. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 14 of 51 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Product data Rev. 05 -- 17 December 2004 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. 9397 750 14467 Philips Semiconductors Table 7: P89LPC906 Special function registers * indicates SFRs that are bit addressable. Name Description SFR addr. Bit address ACC* AUXR1 B* CMP1 DIVM DPTR DPH DPL FMADRH FMADRL FMCON Accumulator Auxiliary function register B register Comparator 1 control register CPU clock divide-by-M control Data pointer (2 bytes) Data pointer high Data pointer low Program Flash address high Program Flash address low Program Flash Control (Read) Program Flash Control (Write) FMDATA IEN0* IEN1* IP0* IP0H Program Flash data Interrupt enable 0 Interrupt enable 1 Interrupt priority 0 Interrupt priority 0 high E5H A8H Bit address E8H Bit address B8H B7H Bit address IP1* IP1H KBCON Interrupt priority 1 Interrupt priority 1 high Keypad control register F8H F7H 94H EA EF BF FF EWDRT EE BE PWDRT PWDRT H FE EBO ED BD PBO PBOH FD EC BC FC ET1 EB BB PT1 PT1H FB EA EC BA FA PC PCH ET0 E9 EKBI B9 PT0 PT0H F9 PKBI PKBIH PATN _SEL E8 B8 F8 KBIF 00[1] 00[1] 00[1] 00x00000 00x00000 xxxxxx00 00[1] 00[1] x0000000 x0000000 00[1] 00x00000 83H 82H E7H E6H E4H BUSY FMCMD. 7 FMCMD. 6 FMCMD. 5 FMCMD. 4 HVA FMCMD. 3 HVE FMCMD. 2 SV FMCMD. 1 OI FMCMD. 0 00 00 00000000 00000000 00 00 00 00 70 00000000 00000000 00000000 00000000 01110000 E0H A2H F0H ACH 95H CE1 CN1 OE1 CO1 CMF1 CLKLP F7 F6 F5 ENT0 F4 SRST F3 0 F2 F1 DPS F0 00 00[1] 00 00000000 xx000000 00000000 Bit address Bit functions and addresses MSB E7 E6 E5 E4 E3 E2 E1 LSB E0 00 00[1] 00000000 000000x0 Reset value Hex Binary 8-bit microcontrollers with two-clock 80C51 core P89LPC906/907/908 15 of 51 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Table 7: P89LPC906 Special function registers...continued * indicates SFRs that are bit addressable. Name KBMASK KBPATN P0* Description Keypad interrupt mask register Keypad pattern register Port 0 SFR addr. 86H 93H Bit address 80H Bit address P1* P3* Rev. 05 -- 17 December 2004 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data 16 of 51 9397 750 14467 Philips Semiconductors Bit functions and addresses MSB LSB Reset value Hex 00 FF Binary 00000000 11111111 87 97 B7 RTCPD D7 CY RTCF 86 CMP1 /KB6 96 B6 - 85 CMPREF /KB5 95 RST B5 - 84 CIN1A /KB4 94 B4 - 83 93 B3 GF1 D3 RS0 - 82 92 B2 GF0 D2 OV R_WD - 81 91 B1 XTAL1 - 80 90 B0 XTAL2 [1] [1] [1] Port 1 Port 3 Port 0 output mode 1 Port 0 output mode 2 Port 1 output mode 1 Port 1 output mode 2 Port 3 output mode 1 Port 3 output mode 2 Power control register Power control register A Program status word Port 0 digital input disable Reset source register Real-time clock control Real-time clock register high Real-time clock register low Stack pointer Timer 0 auxiliary mode Timer 0 and 1 control 90H Bit address B0H 84H 85H 91H 92H B1H B2H 87H B5H Bit address D0H F6H DFH D1H D2H D3H 81H 8FH Bit address 88H P0M1 P0M2 P1M1 P1M2 P3M1 P3M2 PCON PCONA PSW* PT0AD RSTSRC RTCCON RTCH RTCL SP TAMOD TCON* (P0M1.6) (P0M1.5) (P0M1.4) (P0M2.6) (P0M2.5) (P0M2.4) D6 AC RTCS1 (P1M1.5) (P1M2.5) BOPD VCPD D5 F0 PT0AD.5 BOF RTCS0 D4 RS1 PT0AD.4 POF BOI FF 00 FF[1] 00[1] 03[1] 00 00[1] 11111111 00000000 11111111 00000000 xxxxxx11 xxxxxx00 00000000 00000000 00000000 xx00000x 011xxx00 00000000 00000000 00000111 xxx0xxx0 00000000 (P3M1.1) (P3M1.0) PMOD1 D1 F1 R_SF ERTC D0 P R_EX RTCEN PMOD0 8-bit microcontrollers with two-clock 80C51 core (P3M2.1) (P3M2.0) 00[1] P89LPC906/907/908 00 00 [3] 60[1] [6] 00[6] 00[6] 07 8F TF1 8E TR1 8D TF0 8C TR0 8B 8A 89 T0M2 88 00 00 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Table 7: P89LPC906 Special function registers...continued * indicates SFRs that are bit addressable. Name TH0 TH1 TL0 TL1 TMOD TRIM WDCON WDL WFEED1 WFEED2 [1] [2] Rev. 05 -- 17 December 2004 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data 17 of 51 9397 750 14467 Philips Semiconductors Description Timer 0 high Timer 1 high Timer 0 low Timer 1 low Timer 0 and 1 mode Internal oscillator trim register Watchdog control register Watchdog load Watchdog feed 1 Watchdog feed 2 SFR addr. 8CH 8DH 8AH 8BH 89H 96H A7H C1H C2H C3H Bit functions and addresses MSB LSB Reset value Hex 00 00 00 00 Binary 00000000 00000000 00000000 00000000 00000000 PRE2 ENCLK PRE1 T1M1 TRIM.5 PRE0 T1M0 TRIM.4 - TRIM.3 - TRIM.2 WDRUN T0M1 TRIM.1 WDTOF T0M0 TRIM.0 WDCLK 00 [5] [6] [4] [6] FF 11111111 [3] [4] [5] [6] All ports are in input only (high impedance) state after power-up. BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is `0'. If any are written while BRGEN = 1, the result is unpredictable. Unimplemented bits in SFRs (labeled '-') are X (unknown) at all times. Unless otherwise specified, ones should not be written to these bits since they may be used for other purposes in future derivatives. The reset values shown for these bits are `0's although they are unknown when read. The RSTSRC register reflects the cause of the P89LPC906/907/908 reset. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the power-on reset value is xx110000. After reset, the value is 111001x1, i.e., PRE2-PRE0 are all `1', WDRUN = 1 and WDCLK = 1. WDTOF bit is `1' after Watchdog reset and is `0' after power-on reset. Other resets will not affect WDTOF. On power-on reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register. The only reset source that affects these SFRs is power-on reset. 8-bit microcontrollers with two-clock 80C51 core P89LPC906/907/908 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Product data Rev. 05 -- 17 December 2004 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. 9397 750 14467 Philips Semiconductors Table 8: P89LPC907 Special function registers * indicates SFRs that are bit addressable. Name Description SFR addr. Bit address ACC* AUXR1 B* BRGR0[2] BRGR1[2] BRGCON CMP1 DIVM DPTR DPH DPL FMADRH FMADRL FMCON Accumulator Auxiliary function register B register Baud rate generator rate low Baud rate generator rate high Baud rate generator control Comparator 1 control register CPU clock divide-by-M control Data pointer (2 bytes) Data pointer high Data pointer low Program Flash address high Program Flash address low Program Flash Control (Read) Program Flash Control (Write) FMDATA IEN0* IEN1* IP0* IP0H Program Flash data Interrupt enable 0 Interrupt enable 1 Interrupt priority 0 Interrupt priority 0 high E5H A8H Bit address E8H Bit address B8H B7H Bit address IP1* Interrupt priority 1 F8H EA EF BF FF EWDRT EE EST BE PWDRT PWDRT H FE PST EBO ED BD PBO PBOH FD ES EC BC PS PSH FC ET1 EB BB PT1 PT1H FB EA EC BA FA PC ET0 E9 EKBI B9 PT0 PT0H F9 PKBI E8 B8 F8 00[1] 00x00000 00[1] 00[1] x0000000 x0000000 00[1] 00x00000 83H 82H E7H E6H E4H BUSY FMCMD. 7 FMCMD. 6 FMCMD. 5 FMCMD. 4 HVA FMCMD. 3 HVE FMCMD. 2 SV FMCMD. 1 OI FMCMD. 0 00 00 00000000 00000000 00 00 00 00 70 00000000 00000000 00000000 00000000 01110000 E0H A2H F0H BEH BFH BDH ACH 95H CE1 CN1 OE1 SBRGS CO1 BRGEN CMF1 F7 F6 F5 F4 SRST F3 0 F2 F1 DPS F0 00 00 00 00[6] 00[1] 00 00000000 00000000 00000000 xxxxxx00 xx000000 00000000 Bit address Bit functions and addresses MSB E7 E6 E5 E4 E3 E2 E1 LSB E0 00 00[1] 00000000 000000x0 Reset value Hex Binary 8-bit microcontrollers with two-clock 80C51 core P89LPC906/907/908 18 of 51 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Table 8: P89LPC907 Special function registers...continued * indicates SFRs that are bit addressable. Name IP1H KBCON KBMASK KBPATN P0* Description Interrupt priority 1 high Keypad control register Keypad interrupt mask register Keypad pattern register Port 0 SFR addr. F7H 94H 86H 93H Bit address 80H Bit address Rev. 05 -- 17 December 2004 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data 19 of 51 9397 750 14467 Philips Semiconductors Bit functions and addresses MSB PSTH PCH PKBIH PATN _SEL LSB KBIF Reset value Hex 00[1] 00[1] 00 FF Binary 00x00000 xxxxxx00 00000000 11111111 87 97 B7 SMOD1 RTCPD D7 CY RTCF 86 CMP1 /KB6 96 B6 85 CMPREF /KB5 95 RST B5 84 CIN1A /KB4 94 B4 83 93 B3 GF1 D3 RS0 - 82 KB2 92 T0 B2 (P0M1.2) (P0M2.2) (P1M1.2) (P1M2.2) GF0 D2 OV R_WD - 81 91 B1 PMOD1 SPD D1 F1 R_SF ERTC 80 KB0 90 TxD B0 (P0M1.0) FF (P0M2.0) 00 (P1M1.0) PMOD0 D0 P R_EX RTCEN 00 00 [3] [1] P1* P0M1 P0M2 P1M1 P1M2 PCON PCONA PSW* PT0AD RSTSRC RTCCON RTCH RTCL SBUF SCON* Port 1 Port 0 output mode 1 Port 0 output mode 2 Port 1 output mode 1 Port 1 output mode 2 Power control register Power control register A Program status word Port 0 digital input disable Reset source register Real-time clock control Real-time clock register high Real-time clock register low Serial port data buffer register Serial port control 90H Bit address 84H 85H 91H 92H 87H B5H Bit address D0H F6H DFH D1H D2H D3H 99H (P0M1.6) (P0M1.5) (P0M1.4) (P0M2.6) (P0M2.5) (P0M2.4) SMOD0 D6 AC RTCS1 (P1M1.5) (P1M2.5) BOPD VCPD D5 F0 PT0AD.5 BOF RTCS0 D4 RS1 PT0AD.4 POF BOI 11111111 00000000 11111111 FF[1] 00 00[1] 8-bit microcontrollers with two-clock 80C51 core (P1M2.0) 00[1] 00000000 00000000 00000000 00000000 xx00000x 011xxx00 00000000 00000000 xxxxxxxx 00000000 P89LPC906/907/908 60[1] [6] 00[6] 00[6] xx 9F SM0 9E SM1 9D SM2 9C 9B TB8 9A 99 TI 98 00 Bit address 98H xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Table 8: P89LPC907 Special function registers...continued * indicates SFRs that are bit addressable. Name SSTAT SP TAMOD TCON* TH0 TH1 TL0 TL1 TMOD TRIM WDCON WDL WFEED1 WFEED2 [1] [2] Rev. 05 -- 17 December 2004 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data 20 of 51 9397 750 14467 Philips Semiconductors Description Serial port extended status register Stack pointer Timer 0 auxiliary mode Timer 0 and 1 control Timer 0 high Timer 1 high Timer 0 low Timer 1 low Timer 0 and 1 mode Internal oscillator trim register Watchdog control register Watchdog load Watchdog feed 1 Watchdog feed 2 SFR addr. BAH 81H 8FH Bit address 88H 8CH 8DH 8AH 8BH 89H 96H A7H C1H C2H C3H Bit functions and addresses MSB DBMOD INTLO CIDIS DBISEL LSB Reset value Hex 00 07 Binary 00000000 00000111 xxx0xxx0 00000000 00000000 00000000 00000000 00000000 00000000 8F TF1 8E TR1 8D TF0 8C TR0 8B - 8A - 89 - T0M2 88 - 00 00 00 00 00 00 PRE2 PRE1 T1M1 TRIM.5 PRE0 T1M0 TRIM.4 - TRIM.3 - TRIM.2 WDRUN T0M1 TRIM.1 WDTOF T0M0 TRIM.0 WDCLK 00 [5] [6] [4] [6] FF 11111111 8-bit microcontrollers with two-clock 80C51 core [3] [4] [5] [6] All ports are in input only (high impedance) state after power-up. BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is `0'. If any are written while BRGEN = 1, the result is unpredictable. Unimplemented bits in SFRs (labeled '-') are X (unknown) at all times. Unless otherwise specified, ones should not be written to these bits since they may be used for other purposes in future derivatives. The reset values shown for these bits are `0's although they are unknown when read. The RSTSRC register reflects the cause of the P89LPC906/907/908 reset. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the power-on reset value is xx110000. After reset, the value is 111001x1, i.e., PRE2-PRE0 are all `1', WDRUN = 1 and WDCLK = 1. WDTOF bit is `1' after Watchdog reset and is `0' after power-on reset. Other resets will not affect WDTOF. On power-on reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register. The only reset source that affects these SFRs is power-on reset. P89LPC906/907/908 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Product data Rev. 05 -- 17 December 2004 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. 9397 750 14467 Philips Semiconductors Table 9: P89LPC908 Special function registers * indicates SFRs that are bit addressable. Name Description SFR addr. Bit address ACC* AUXR1 B* BRGR0[2] BRGR1[2] BRGCON CMP1 DIVM DPTR DPH DPL FMADRH FMADRL FMCON Accumulator Auxiliary function register B register Baud rate generator rate low Baud rate generator rate high Baud rate generator control Comparator 1 control register CPU clock divide-by-M control Data pointer (2 bytes) Data pointer high Data pointer low Program Flash address high Program Flash address low Program Flash Control (Read) Program Flash Control (Write) FMDATA IEN0* IEN1* IP0* IP0H Program Flash data Interrupt enable 0 Interrupt enable 1 Interrupt priority 0 Interrupt priority 0 high E5H A8H Bit address E8H Bit address B8H B7H Bit address IP1* Interrupt priority 1 F8H EA EF BF FF EWDRT EE EST BE PWDRT PWDRT H FE PST EBO ED BD PBO PBOH FD ES/ESR EC BC PS/PSR PSH /PSRH FC ET1 EB BB PT1 PT1H FB EA EC BA FA PC ET0 E9 EKBI B9 PT0 PT0H F9 PKBI E8 B8 F8 00[1] 00x00000 00[1] 00[1] x0000000 x0000000 00[1] 00x00000 83H 82H E7H E6H E4H BUSY FMCMD. 7 FMCMD. 6 FMCMD. 5 FMCMD. 4 HVA FMCMD. 3 HVE FMCMD. 2 SV FMCMD. 1 OI FMCMD. 0 00 00 00000000 00000000 00 00 00 00 70 00000000 00000000 00000000 00000000 01110000 E0H A2H F0H BEH BFH BDH ACH 95H CE1 CN1 OE1 SBRGS CO1 BRGEN CMF1 F7 EBRR F6 F5 F4 SRST F3 0 F2 F1 DPS F0 00 00 00 00[6] 00[1] 00 00000000 00000000 00000000 xxxxxx00 xx000000 00000000 Bit address Bit functions and addresses MSB E7 E6 E5 E4 E3 E2 E1 LSB E0 00 00[1] 00000000 000000x0 Reset value Hex Binary 8-bit microcontrollers with two-clock 80C51 core P89LPC906/907/908 21 of 51 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Table 9: P89LPC908 Special function registers...continued * indicates SFRs that are bit addressable. Name IP1H KBCON KBMASK KBPATN P0* Description Interrupt priority 1 high Keypad control register Keypad interrupt mask register Keypad pattern register Port 0 SFR addr. F7H 94H 86H 93H Bit address 80H Bit address Rev. 05 -- 17 December 2004 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data 22 of 51 9397 750 14467 Philips Semiconductors Bit functions and addresses MSB PSTH PCH PKBIH PATN _SEL LSB KBIF Reset value Hex 00[1] 00[1] 00 FF Binary 00x00000 xxxxxx00 00000000 11111111 87 97 SMOD1 RTCPD D7 CY RTCF 86 CMP1 /KB6 96 - 85 CMPREF /KB5 95 RST 84 CIN1A /KB4 94 - 83 93 GF1 D3 RS0 R_BK - 82 KB2 92 (P0M1.2) (P0M2.2) GF0 D2 OV PT0AD.2 R_WD - 81 91 RxD - 80 90 TxD FF 00 FF[1] 00[1] 00 00[1] D0 P R_EX RTCEN 00 00 [3] [1] P1* P0M1 P0M2 P1M1 P1M2 PCON PCONA PSW* PT0AD RSTSRC RTCCON RTCH RTCL SADDR SADEN SBUF SCON* Port 1 Port 0 output mode 1 Port 0 output mode 2 Port 1 output mode 1 Port 1 output mode 2 Power control register Power control register A Program status word Port 0 digital input disable Reset source register Real-time clock control Real-time clock register high Real-time clock register low Serial port address register Serial port address enable Serial port data buffer register Serial port control 90H 84H 85H 91H 92H 87H B5H Bit address D0H F6H DFH D1H D2H D3H A9H B9H 99H (P0M1.6) (P0M1.5) (P0M1.4) (P0M2.6) (P0M2.5) (P0M2.4) SMOD0 D6 AC RTCS1 (P1M1.5) (P1M2.5) BOPD VCPD D5 F0 PT0AD.5 BOF RTCS0 D4 RS1 PT0AD.4 POF BOI 11111111 00000000 11111111 00000000 (P1M1.1) (P1M1.0) (P1M2.1) (P1M2.0) PMOD1 SPD D1 F1 R_SF ERTC PMOD0 8-bit microcontrollers with two-clock 80C51 core 00000000 00000000 00000000 xx00000x 011xxx00 00000000 00000000 00000000 00000000 xxxxxxxx 00000000 P89LPC906/907/908 60[1] [6] 00[6] 00[6] 00 00 xx 9F SM0/FE 9E SM1 9D SM2 9C REN 9B TB8 9A RB8 99 TI 98 RI 00 Bit address 98H xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Table 9: P89LPC908 Special function registers...continued * indicates SFRs that are bit addressable. Name SSTAT SP TCON* TH0 TH1 TL0 TL1 TMOD TRIM WDCON WDL WFEED1 WFEED2 [1] [2] Rev. 05 -- 17 December 2004 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data 23 of 51 9397 750 14467 Philips Semiconductors Description Serial port extended status register Stack pointer Timer 0 and 1 control Timer 0 high Timer 1 high Timer 0 low Timer 1 low Timer 0 and 1 mode Internal oscillator trim register Watchdog control register Watchdog load Watchdog feed 1 Watchdog feed 2 SFR addr. BAH 81H Bit address 88H 8CH 8DH 8AH 8BH 89H 96H A7H C1H C2H C3H Bit functions and addresses MSB DBMOD INTLO CIDIS DBISEL FE BR OE LSB STINT Reset value Hex 00 07 Binary 00000000 00000111 00000000 00000000 00000000 00000000 00000000 00000000 8F TF1 8E TR1 8D TF0 8C TR0 8B - 8A - 89 - 88 00 00 00 00 00 PRE2 PRE1 T1M1 TRIM.5 PRE0 T1M0 TRIM.4 - TRIM.3 - TRIM.2 WDRUN T0M1 TRIM.1 WDTOF T0M0 TRIM.0 WDCLK 00 [5] [6] [4] [6] FF 11111111 8-bit microcontrollers with two-clock 80C51 core [3] [4] [5] [6] All ports are in input only (high impedance) state after power-up. BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is `0'. If any are written while BRGEN = 1, the result is unpredictable. Unimplemented bits in SFRs (labeled '-') are X (unknown) at all times. Unless otherwise specified, ones should not be written to these bits since they may be used for other purposes in future derivatives. The reset values shown for these bits are `0's although they are unknown when read. The RSTSRC register reflects the cause of the P89LPC906/907/908 reset. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the power-on reset value is xx110000. After reset, the value is 111001x1, i.e., PRE2-PRE0 are all `1', WDRUN = 1 and WDCLK = 1. WDTOF bit is `1' after Watchdog reset and is `0' after power-on reset. Other resets will not affect WDTOF. On power-on reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register. The only reset source that affects these SFRs is power-on reset. P89LPC906/907/908 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 8. Functional description Remark: Please refer to the P89LPC906/907/908 User's Manual for a more detailed functional description. 8.1 Enhanced CPU The P89LPC906/907/908 uses an enhanced 80C51 CPU which runs at 6 times the speed of standard 80C51 devices. A machine cycle consists of two CPU clock cycles, and most instructions execute in one or two machine cycles. 8.2 Clocks 8.2.1 Clock definitions The P89LPC906/907/908 device has several internal clocks as defined below: OSCCLK -- Input to the DIVM clock divider. OSCCLK is selected from one of the clock sources (see Figure 10 and 11) and can also be optionally divided to a slower frequency (see Section 8.7 "CPU CLOCK (CCLK) modification: DIVM register"). Note: fosc is defined as the OSCCLK frequency. CCLK -- CPU clock; output of the clock divider. There are two CCLK cycles per machine cycle, and most instructions are executed in one to two machine cycles (two or four CCLK cycles). RCCLK -- The internal 7.373 MHz RC oscillator output. PCLK -- Clock for the various peripheral devices and is CCLK/2 8.2.2 CPU clock (OSCCLK) The P89LPC906/907/908 provides several user-selectable oscillator options in generating the CPU clock. This allows optimization for a range of needs from high precision to lowest possible cost. These options are configured when the FLASH is programmed and include an on-chip Watchdog oscillator and an on-chip RC oscillator. The P89LPC906, in addition, includes an option for an oscillator using an external crystal or an external clock source. The crystal oscillator can be optimized for low, medium, or high frequency crystals covering a range from 20 kHz to 12 MHz. 8.2.3 Low speed oscillator option (P89LPC906) This option supports an external crystal in the range of 20 kHz to 100 kHz. Ceramic resonators are also supported in this configuration. 8.2.4 Medium speed oscillator option (P89LPC906) This option supports an external crystal in the range of 100 kHz to 4 MHz. Ceramic resonators are also supported in this configuration. 8.2.5 High speed oscillator option (P89LPC906) This option supports an external crystal in the range of 4 MHz to 18 MHz. Ceramic resonators are also supported in this configuration. When using an oscillator frequency above 12 MHz, the reset input function of P1.5 must be enabled. An 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 24 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core external circuit is required to hold the device in reset at power-up until VDD has reached its specified level. When system power is removed VDD will fall below the minimum specified operating voltage. When using an oscillator frequency above 12 MHz, in some applications, an external brownout detect circuit may be required to hold the device in reset when VDD falls below the minimum specified operating voltage. If CCLK is 8 MHz or slower, the CLKLP SFR bit (AUXR1.7) can be set to `1' to reduce power consumption. On reset, CLKLP is `0' allowing highest performance access. This bit can then be set in software if CCLK is running at 8 MHz or slower. 8.2.6 Clock output (P89LPC906) The P89LPC906 supports a user selectable clock output function on the XTAL2/CLKOUT pin when crystal oscillator is not being used. This condition occurs if another clock source has been selected (on-chip RC oscillator, Watchdog oscillator, external clock input on X1) and if the Real-Time clock is not using the crystal oscillator as its clock source. This allows external devices to synchronize to the P89LPC906. This output is enabled by the ENCLK bit in the TRIM register. The frequency of this clock output is 12 that of the CCLK. If the clock output is not needed in Idle mode, it may be turned off prior to entering Idle, saving additional power. 8.3 On-chip RC oscillator option The P89LPC906/907/908 has a 6-bit TRIM register that can be used to tune the frequency of the RC oscillator. During reset, the TRIM value is initialized to a factory pre-programmed value to adjust the oscillator frequency to 7.373 MHz, 2.5 %. End-user applications can write to the Trim register to adjust the on-chip RC oscillator to other frequencies. If CCLK is 8 MHz or slower, the CLKLP SFR bit (AUXR1.7) can be set to `1' to reduce power consumption. On reset, CLKLP is `0' allowing highest performance access. This bit can then be set in software if CCLK is running at 8 MHz or slower. 8.4 Watchdog oscillator option The watchdog has a separate oscillator which has a frequency of 400 kHz. This oscillator can be used to save power when a high clock frequency is not needed. 8.5 External clock input option (P89LPC906) In this configuration, the processor clock is derived from an external source driving the XTAL1/P3.1 pin. The rate may be from 0 Hz up to 18 MHz. The XTAL2/P3.0 pin may be used as a standard port pin or a clock output. When using an oscillator frequency above 12 MHz, the reset input function of P1.5 must be enabled. An external circuit is required to hold the device in reset at power-up until VDD has reached its specified level. When system power is removed VDD will fall below the minimum specified operating voltage. When using an oscillator frequency above 12 MHz, in some applications, an external brownout detect circuit may be required to hold the device in reset when VDD falls below the minimum specified operating voltage. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 25 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core XTAL1 XTAL2 High freq. Med. freq. Low freq. OSCCLK CCLK RTC DIVM CPU RC OSCILLATOR (7.3728 MHz) WATCHDOG OSCILLATOR (400 kHz) 2 WDT PCLK TIMERS 0 & 1 002aaa447 Fig 10. Block diagram of oscillator control (P89LPC906). RTC RC OSCILLATOR (7.3728 MHz) OSCCLK DIVM CCLK CPU 2 WATCHDOG OSCILLATOR (400 kHz) PCLK WDT TIMERS 0 & 1 BAUD RATE GENERATOR 002aaa449 UART Fig 11. Block diagram of oscillator control (P89LPC907, P89LPC908). 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 26 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 8.6 CPU CLock (CCLK) wake-up delay The P89LPC906/907/908 has an internal wake-up timer that delays the clock until it stabilizes depending to the clock source used. If the clock source is any of the three crystal selections (P89LPC906) the delay is 992 OSCCLK cycles plus 60 to 100 s. 8.7 CPU CLOCK (CCLK) modification: DIVM register The OSCCLK frequency can be divided down up to 510 times by configuring a dividing register, DIVM, to generate CCLK. This feature makes it possible to temporarily run the CPU at a lower rate, reducing power consumption. By dividing the clock, the CPU can retain the ability to respond to events that would not exit Idle mode by executing its normal program at a lower rate. This can also allow bypassing the oscillator start-up time in cases where Power-down mode would otherwise be used. The value of DIVM may be changed by the program at any time without interrupting code execution. 8.8 Low power select The P89LPC906 is designed to run at 18 MHz (CCLK) maximum. However, if CCLK is 8 MHz or slower, the CLKLP SFR bit (AUXR1.7) can be set to `1' to lower the power consumption further. On any reset, CLKLP is `0' allowing highest performance access. This bit can then be set in software if CCLK is running at 8 MHz or slower. 8.9 Memory organization The various P89LPC906/907/908 memory spaces are as follows: * DATA 128 bytes of internal data memory space (00h:7Fh) accessed via direct or indirect addressing, using instructions other than MOVX and MOVC. All or part of the Stack may be in this area. * SFR Special Function Registers. Selected CPU registers and peripheral control and status registers, accessible only via direct addressing. * CODE 64 kB of Code memory space, accessed as part of program execution and via the MOVC instruction. The P89LPC906/907/908 has 1 kB of on-chip Code memory. 8.9.1 Data RAM arrangement The 128 bytes of on-chip RAM is organized as follows: Table 10: Type DATA On-chip data memory usages Data RAM Size (Bytes) Memory that can be addressed directly and indirectly 128 8.10 Interrupts The P89LPC906/907/908 uses a four priority level interrupt structure. This allows great flexibility in controlling the handling of the many interrupt sources. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 27 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core The P89LPC906 supports 6 interrupt sources: timers 0 and 1, brownout detect, watchdog/real-time clock, keyboard, and the comparator. The P89LPC907 supports 8 interrupt sources: timers 0 and 1, serial port Tx, combined serial port Rx/Tx (no Rx function is available on this device), brownout detect, watchdog/real-time clock, keyboard, and the comparator. The P89LPC908 supports 9 interrupt sources: timers 0 and 1, serial port Tx, serial port Rx, combined serial port Rx/Tx, brownout detect, watchdog/real-time clock, keyboard, and the comparator. Each interrupt source can be individually enabled or disabled by setting or clearing a bit in the interrupt enable registers IEN0 or IEN1. The IEN0 register also contains a global disable bit, EA, which disables all interrupts. Each interrupt source can be individually programmed to one of four priority levels by setting or clearing bits in the interrupt priority registers IP0, IP0H, IP1, and IP1H. An interrupt service routine in progress can be interrupted by a higher priority interrupt, but not by another interrupt of the same or lower priority. The highest priority interrupt service cannot be interrupted by any other interrupt source. If two requests of different priority levels are pending at the start of an instruction, the request of higher priority level is serviced. If requests of the same priority level are pending at the start of an instruction, an internal polling sequence determines which request is serviced. This is called the arbitration ranking. Note that the arbitration ranking is only used to resolve pending requests of the same priority level. 8.10.1 External interrupt inputs The P89LPC906/907/908 has a Keypad Interrupt function. This can be used as an external interrupt input. If enabled when the P89LPC906/907/908 is put into Power-down or Idle mode, the interrupt will cause the processor to wake-up and resume operation. Refer to Section 8.13 "Power reduction modes" for details. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 28 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core BOF EBO RTCF ERTC (RTCCON.1) WDOVF KBIF EKBI EWDRT CMF EC EA (IE0.7) WAKE-UP (IF IN POWER-DOWN) TF1 ET1 INTERRUPT TO CPU TF0 ET0 002aaa465 Fig 12. Interrupt sources, interrupt enables, and power-down wake-up sources (P89LPC906). BOF EBO RTCF ERTC (RTCCON.1) WDOVF KBIF EKBI EWDRT CMF EC EA (IE0.7) TF1 ET1 TI ES TI EST TF0 ET0 002aaa466 WAKE-UP (IF IN POWER-DOWN) INTERRUPT TO CPU Fig 13. Interrupt sources, interrupt enables, and power-down wake-up sources (P89LPC907). 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 29 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core BOF EBO RTCF ERTC (RTCCON.1) WDOVF KBIF EKBI EWDRT CMF EC EA (IE0.7) TF1 ET1 TI & RI/RI ES/ESR TI EST TF0 ET0 002aaa467 WAKE-UP (IF IN POWER-DOWN) INTERRUPT TO CPU Fig 14. Interrupt sources, interrupt enables, and power-down wake-up sources (P89LPC908). 8.11 I/O ports The P89LPC906 has between 3 and 6 I/O pins: P0.4, P0.5, P0.6, P1.5, P3.0, and P3.1 The exact number of I/O pins available depends on the clock and reset options chosen, as shown in Table 11. Table 11: Number of I/O pins available Reset option No external reset (except during power-up) External RST pin supported External clock input Low/medium/high speed oscillator (external crystal or resonator) [1] Required for operation above 12 MHz. Clock source On-chip oscillator or Watchdog oscillator Number of I/O pins (8-pin package) 6 5 5 4 4 3 No external reset (except during power-up) External RST pin supported[1] No external reset (except during power-up) External RST pin supported[1] The P89LPC907 and P89LPC908 devices have either 5 or 6 I/O pins depending on the reset pin option chosen. 8.11.1 Port configurations All but one I/O port pin on the P89LPC906/907/908 may be configured by software to one of four types on a bit-by-bit basis. These are: quasi-bidirectional (standard 80C51 port outputs), push-pull, open drain, and input-only. Two configuration registers for each port select the output type for each port pin. P1.5 (RST) can only be an input and cannot be configured. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 30 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 8.11.2 Quasi-bidirectional output configuration Quasi-bidirectional output type can be used as both an input and output without the need to reconfigure the port. This is possible because when the port outputs a logic HIGH, it is weakly driven, allowing an external device to pull the pin LOW. When the pin is driven LOW, it is driven strongly and able to sink a fairly large current. These features are somewhat similar to an open-drain output except that there are three pull-up transistors in the quasi-bidirectional output that serve different purposes. The P89LPC906/907/908 are 3 V devices, however, the pins are 5 V-tolerant (except for XTAL1 and XTAL2). In quasi-bidirectional mode, if a user applies 5 V on the pin, there will be a current flowing from the pin to VDD, causing extra power consumption. Therefore, applying 5 V in quasi-bidirectional mode is discouraged. A quasi-bidirectional port pin has a Schmitt-triggered input that also has a glitch suppression circuit. 8.11.3 Open-drain output configuration The open-drain output configuration turns off all pull-ups and only drives the pull-down transistor of the port driver when the port latch contains a logic `0'. To be used as a logic output, a port configured in this manner must have an external pull-up, typically a resistor tied to VDD. An open-drain port pin has a Schmitt-triggered input that also has a glitch suppression circuit. 8.11.4 Input-only configuration The input-only port configuration has no output drivers. It is a Schmitt-triggered input that also has a glitch suppression circuit. 8.11.5 Push-pull output configuration The push-pull output configuration has the same pull-down structure as both the open-drain and the quasi-bidirectional output modes, but provides a continuous strong pull-up when the port latch contains a logic `1'. The push-pull mode may be used when more source current is needed from a port output. A push-pull port pin has a Schmitt-triggered input that also has a glitch suppression circuit. 8.11.6 Port 0 analog functions The P89LPC906/907/908 incorporates an Analog Comparator. In order to give the best analog function performance and to minimize power consumption, pins that are being used for analog functions must have the digital outputs and digital inputs disabled. Digital outputs are disabled by putting the port output into the Input-Only (high impedance) mode as described in Section 8.11.4 "Input-only configuration". Digital inputs on Port 0 may be disabled through the use of the PT0AD register. On any reset, the PT0AD bits default to `0's to enable digital functions. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 31 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 8.11.7 Additional port features After power-up, all pins are in Input-Only mode. Please note that this is different from the LPC76x series of devices. * After power-up all I/O pins, except P1.5, may be configured by software. * Pin P1.5 is input only. Every output on the P89LPC906/907/908 has been designed to sink typical LED drive current. However, there is a maximum total output current for all ports which must not be exceeded. Please refer to Table 13 "DC electrical characteristics" for detailed specifications. All ports pins that can function as an output have slew rate controlled outputs to limit noise generated by quickly switching output signals. The slew rate is factory-set to approximately 10 ns rise and fall times. 8.12 Power monitoring functions The P89LPC906/907/908 devices incorporate power monitoring functions designed to prevent incorrect operation during initial power-up and power loss or reduction during operation. This is accomplished with two hardware functions: Power-on Detect and Brownout detect. 8.12.1 Brownout detection The Brownout detect function determines if the power supply voltage drops below a certain level. The default operation is for a Brownout detection to cause a processor reset, however, it may alternatively be configured to generate an interrupt. Brownout detection may be enabled or disabled in software. If Brownout detection is enabled, the brownout condition occurs when VDD falls below the brownout trip voltage, VBO (see Table 13 "DC electrical characteristics"), and is negated when VDD rises above VBO. If the P89LPC906/907/908 device is to operate with a power supply that can be below 2.7 V, BOE should be left in the unprogrammed state so that the device can operate at 2.4 V, otherwise continuous brownout reset may prevent the device from operating. For correct activation of Brownout detect, the VDD rise and fall times must be observed. Please see Table 13 "DC electrical characteristics" for specifications. 8.12.2 Power-on detection The Power-on Detect has a function similar to the Brownout detect, but is designed to work as power comes up initially, before the power supply voltage reaches a level where Brownout detect can work. The POF flag in the RSTSRC register is set to indicate an initial power-up condition. The POF flag will remain set until cleared by software. 8.13 Power reduction modes The P89LPC906/907/908 supports three different power reduction modes. These modes are Idle mode, Power-down mode, and total Power-down mode. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 32 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 8.13.1 Idle mode Idle mode leaves peripherals running in order to allow them to activate the processor when an interrupt is generated. Any enabled interrupt source or reset may terminate Idle mode. 8.13.2 Power-down mode The Power-down mode stops the oscillator in order to minimize power consumption. The P89LPC906/907/908 exits Power-down mode via any reset, or certain interrupts. In Power-down mode, the power supply voltage may be reduced to the RAM keep-alive voltage VRAM. This retains the RAM contents at the point where Power-down mode was entered. SFR contents are not guaranteed after VDD has been lowered to VRAM, therefore it is highly recommended to wake up the processor via reset in this case. VDD must be raised to within the operating range before the Power-down mode is exited. Some chip functions continue to operate and draw power during Power-down mode, increasing the total power used during Power-down. These include: Brownout detect, Watchdog Timer, Comparator (Note: Comparator can be powered-down separately), and Real-Time Clock (RTC)/System Timer. The internal RC oscillator is disabled unless both the RC oscillator has been selected as the system clock and the RTC is enabled. 8.13.3 Total Power-down mode This is the same as Power-down mode except that the brownout detection circuitry and the voltage comparators are also disabled to conserve additional power. The internal RC oscillator is disabled unless both the RC oscillator has been selected as the system clock and the RTC is enabled. If the internal RC oscillator is used to clock the RTC during Power-down, there will be high power consumption. Please use an external low frequency clock to achieve low power with the Real-Time Clock running during Power-down. 8.14 Reset The P1.5/RST pin can function as either an active-LOW reset input or as a digital input, P1.5. The RPE (Reset Pin Enable) bit in UCFG1, when set to `1', enables the external reset input function on P1.5. When cleared, P1.5 may be used as an input pin. Remark: During a power-up sequence, the RPE selection is overridden and this pin will always function as a reset input. An external circuit connected to this pin should not hold this pin LOW during a power-on sequence as this will keep the device in reset. After power-up this input will function either as an external reset input or as a digital input as defined by the RPE bit. Only a power-up reset will temporarily override the selection defined by RPE bit. Other sources of reset will not override the RPE bit. Remark: During a power cycle, VDD must fall below VPOR (see Table 13 "DC electrical characteristics") before power is reapplied, in order to ensure a power-on reset. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 33 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core Reset can be triggered from the following sources: * External reset pin (during power-up or if user configured via UCFG1. This option must be used for an oscillator frequency above 12 MHz (P89LPC906).) * * * * * Power-on detect Brownout detect Watchdog Timer Software reset UART break character detect reset (P89LPC908). For every reset source, there is a flag in the Reset Register, RSTSRC. The user can read this register to determine the most recent reset source. These flag bits can be cleared in software by writing a `0' to the corresponding bit. More than one flag bit may be set: * During a power-on reset, both POF and BOF are set but the other flag bits are cleared. * For any other reset, previously set flag bits that have not been cleared will remain set. 8.15 Timers/counters 0 and 1 The P89LPC906/907/908 has two general purpose timers which are similar to the standard 80C51 Timer 0 and Timer 1. These timers have four operating modes (modes 0, 1, 2, and 3). Modes 0, 1, and 2 are the same for both Timers. Mode 3 is different. And additional PWM output mode, Mode 6, is provided on the P89LPC907. 8.15.1 Mode 0 Putting either Timer into Mode 0 makes it look like an 8048 Timer, which is an 8-bit Counter with a divide-by-32 prescaler. In this mode, the Timer register is configured as a 13-bit register. Mode 0 operation is the same for Timer 0 and Timer 1. 8.15.2 Mode 1 Mode 1 is the same as Mode 0, except that all 16 bits of the timer register are used. 8.15.3 Mode 2 Mode 2 configures the Timer register as an 8-bit Counter with automatic reload. Mode 2 operation is the same for Timer 0 and Timer 1. 8.15.4 Mode 3 When Timer 1 is in Mode 3 it is stopped. Timer 0 in Mode 3 forms two separate 8-bit counters and is provided for applications that require an extra 8-bit timer. When Timer 1 is in Mode 3 it can still be used by the serial port as a baud rate generator for the P89LPC907 and P89LPC908. 8.15.5 Mode 6 (P89LPC907) In this mode, the corresponding timer can be changed to a PWM with a full period of 256 timer clocks. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 34 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 8.15.6 Timer overflow toggle output (P89LPC907) Timers 0 and 1 can be configured to automatically toggle a port output whenever a timer overflow occurs. The same device pins that are used for the T0 and T1 count inputs are also used for the timer toggle outputs. The port outputs will be a logic 1 prior to the first timer overflow when this mode is turned on. 8.16 Real-Time clock/system timer The P89LPC906/907/908 has a simple Real-Time clock that allows a user to continue running an accurate timer while the rest of the device is powered-down. The Real-Time clock can be a wake-up or an interrupt source. The Real-Time clock is a 23-bit down counter comprised of a 7-bit prescaler and a 16-bit loadable down counter. When it reaches all `0's, the counter will be reloaded again and the RTCF flag will be set. The clock source for this counter can be either the CPU clock (CCLK) or the XTAL oscillator, provided that the XTAL oscillator is not being used as the CPU clock. If the XTAL oscillator is used as the CPU clock, then the RTC will use CCLK as its clock source. Only power-on reset will reset the Real-Time clock and its associated SFRs to the default state. 8.17 UART (P89LPC908) The P89LPC907 and P89LPC908 devices have an enhanced UART that is compatible with the conventional 80C51 UART except that Timer 2 overflow cannot be used as a baud rate source. The P89LPC907 does not have an RxD pin and thus receiver functions described in this section do not apply to the P89LPC907. Both devices include an independent Baud Rate Generator. The baud rate can be selected from the OSCCLK (divided by a constant), Timer 1 overflow, or the independent Baud Rate Generator. In addition to the baud rate generation, enhancements over the standard 80C51 UART include Framing Error detection, automatic address recognition, selectable double buffering and several interrupt options. The UART can be operated in 4 modes: shift register, 8-bit UART, 9-bit UART, and CCLK/32 or CCLK/16. 8.17.1 Mode 0 Serial data enters and exits through RxD. TxD outputs the shift clock. 8 bits are transmitted or received, LSB first. The baud rate is fixed at 116 of the CPU clock frequency. 8.17.2 Mode 1 10 bits are transmitted (through TxD) or received (through RxD): a start bit (logical `0'), 8 data bits (LSB first), and a stop bit (logical `1'). When data is received, the stop bit is stored in RB8 in Special Function Register SCON. The baud rate is variable and is determined by the Timer 1 overflow rate or the Baud Rate Generator (described in Section 8.17.5 "Baud rate generator and selection"). 8.17.3 Mode 2 11 bits are transmitted (through TxD) or received (through RxD): start bit (logical `0'), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (logical `1'). When data is transmitted, the 9th data bit (TB8 in SCON) can be assigned the value of `0' or `1'. Or, for example, the parity bit (P, in the PSW) could be moved into TB8. When 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 35 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core data is received, the 9th data bit goes into RB8 in Special Function Register SCON, while the stop bit is not saved. The baud rate is programmable to either 116 or 132 of the CPU clock frequency, as determined by the SMOD1 bit in PCON. 8.17.4 Mode 3 11 bits are transmitted (through TxD) or received (through RxD): a start bit (logical `0'), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (logical `1'). In fact, Mode 3 is the same as Mode 2 in all respects except baud rate. The baud rate in Mode 3 is variable and is determined by the Timer 1 overflow rate or the Baud Rate Generator (described in section Section 8.17.5 "Baud rate generator and selection"). 8.17.5 Baud rate generator and selection Both devices have an independent Baud Rate Generator. The baud rate is determined by a baud-rate preprogrammed into the BRGR1 and BRGR0 SFRs which together form a 16-bit baud rate divisor value that works in a similar manner as Timer 1. If the baud rate generator is used, Timer 1 can be used for other timing functions. The UART can use either Timer 1 or the baud rate generator output (see Figure 15). Note that Timer T1 is further divided by 2 if the SMOD1 bit (PCON.7) is cleared. The independent Baud Rate Generator uses CCLK. Timer 1 Overflow (PCLK-based) Baud Rate Generator (CCLK-based) SMOD1 = 1 SBRGS = 0 Baud Rate Modes 1 and 3 2 SMOD1 = 0 SBRGS = 1 002aaa419 Fig 15. Baud rate sources for UART (Modes 1, 3). 8.17.6 Framing error Framing error is reported in the status register (SSTAT). In addition, if SMOD0 (PCON.6) is `1', framing errors can be made available in SCON.7, respectively. If SMOD0 is `0', SCON.7 is SM0. It is recommended that SM0 and SM1 (SCON.7:6) are set up when SMOD0 is `0'. 8.17.7 Break detect Break detect is reported in the status register (SSTAT). A break is detected when 11 consecutive bits are sensed LOW. The break detect can be used to reset the device. 8.17.8 Double buffering The UART has a transmit double buffer that allows buffering of the next character to be written to SBUF while the first character is being transmitted. Double buffering allows transmission of a string of characters with only one stop bit between any two characters, as long as the next character is written between the start bit and the stop bit of the previous character. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 36 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core Double buffering can be disabled. If disabled (DBMOD, i.e., SSTAT.7 = `0'), the UART is compatible with the conventional 80C51 UART. If enabled, the UART allows writing to SnBUF while the previous data is being shifted out. Double buffering is only allowed in Modes 1, 2 and 3. When operated in Mode 0, double buffering must be disabled (DBMOD = `0'). 8.17.9 Transmit interrupts with double buffering enabled (Modes 1, 2 and 3) Unlike the conventional UART, in double buffering mode, the Tx interrupt is generated when the double buffer is ready to receive new data. 8.17.10 The 9th bit (bit 8) in double buffering (Modes 1, 2 and 3) If double buffering is disabled TB8 can be written before or after SBUF is written, as long as TB8 is updated some time before that bit is shifted out. TB8 must not be changed until the bit is shifted out, as indicated by the Tx interrupt. If double buffering is enabled, TB8 must be updated before SBUF is written, as TB8 will be double-buffered together with SBUF data. 8.18 Analog comparator An analog comparator is provided on the P89LPC906/907/908. Comparator operation is such that the output is a logical one (which may be read in a register) when the positive input is greater than the negative input (selectable from a pin or an internal reference voltage). Otherwise the output is a zero. The comparator may be configured to cause an interrupt when the output value changes. The connections to the comparator are shown in Figure 16. The comparator functions to VDD = 2.4 V. When the comparator is first enabled, the comparator output and interrupt flag are not guaranteed to be stable for 10 microseconds. The comparator interrupt should not be enabled during that time, and the comparator interrupt flag must be cleared before the interrupt is enabled in order to prevent an immediate interrupt service. When a comparator is disabled the comparator's output, COx, goes HIGH. If the comparator output was LOW and then is disabled, the resulting transition of the comparator output from a LOW to HIGH state will set the comparator flag, CMFx. This will cause an interrupt if the comparator interrupt is enabled. The user should therefore disable the comparator interrupt prior to disabling the comparator. Additionally, the user should clear the comparator flag, CMFx, after disabling the comparator. 8.19 Internal reference voltage An internal reference voltage generator may supply a default reference when a single comparator input pin is used. The value of the internal reference voltage, referred to as VREF, is 1.23 V 10 %. 8.20 Comparator interrupt Each comparator has an interrupt flag contained in its configuration register. This flag is set whenever the comparator output changes state. The flag may be polled by software or may be used to generate an interrupt. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 37 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core Comparator (P0.4) CIN1A CO1 (P0.5) CMPREF VREF CN OE1 CMP1 (P0.6) 002aaa468 Change Detect CMF1 EC Interrupt Fig 16. Comparator input and output connections. 8.21 Comparator and power reduction modes The comparator may remain enabled when Power-down or Idle mode is activated, but the comparator is disabled automatically in Total Power-down mode. If the comparator interrupt is enabled (except in Total Power-down mode), a change of the comparator output state will generate an interrupt and wake up the processor. If the comparator output to a pin is enabled, the pin should be configured in the push-pull mode in order to obtain fast switching times while in Power-down mode. The reason is that with the oscillator stopped, the temporary strong pull-up that normally occurs during switching on a quasi-bidirectional port pin does not take place. The comparator consumes power in Power-down and Idle modes, as well as in the normal operating mode. This fact should be taken into account when system power consumption is an issue. To minimize power consumption, the user can disable the comparator via PCONA.5 or put the device in Total Power-down mode. 8.22 Keypad interrupt (KBI) The Keypad Interrupt function is intended primarily to allow a single interrupt to be generated when Port 0 is equal to or not equal to a certain pattern. This function can be used for bus address recognition or keypad recognition. The user can configure the port via SFRs for different tasks. The Keypad Interrupt Mask Register (KBMASK) is used to define which input pins connected to Port 0 can trigger the interrupt. The Keypad Pattern Register (KBPATN) is used to define a pattern that is compared to the value of Port 0. The Keypad Interrupt Flag (KBIF) in the Keypad Interrupt Control Register (KBCON) is set when the condition is matched while the Keypad Interrupt function is active. An interrupt will be generated if enabled. The PATN_SEL bit in the Keypad Interrupt Control Register (KBCON) is used to define equal or not-equal for the comparison. In order to use the Keypad Interrupt as an original KBI function like in 87LPC76x series, the user needs to set KBPATN = 0FFH and PATN_SEL = 1 (not equal), then any key connected to Port 0 which is enabled by the KBMASK register will cause the hardware to set KBIF and generate an interrupt if it has been enabled. The interrupt 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 38 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core may be used to wake up the CPU from Idle or Power down modes. This feature is particularly useful in handheld, battery powered systems that need to carefully manage power consumption yet also need to be convenient to use. In order to set the flag and cause an interrupt, the pattern on Port 0 must be held longer than 6 CCLKs. 8.23 Watchdog timer The watchdog timer causes a system reset when it underflows as a result of a failure to feed the timer prior to the timer reaching its terminal count. It consists of a programmable 12-bit prescaler, and an 8-bit down counter. The down counter is decremented by a tap taken from the prescaler. The clock source for the prescaler is either the PCLK or the nominal 400 kHz Watchdog oscillator. The watchdog timer can only be reset by a power-on reset. When the Watchdog feature is disabled, it can be used as an interval timer and may generate an interrupt. Figure 17 shows the watchdog timer in Watchdog mode. Feeding the Watchdog requires a two-byte sequence. If PCLK is selected as the Watchdog clock and the CPU is powered-down, the watchdog is disabled. The watchdog timer has a time-out period that ranges from a few s to a few seconds. Please refer to the P89LPC906/907/908 User's Manual for more details. WDL (C1H) MOV WFEED1, #0A5H MOV WFEED2, #05AH Watchdog oscillator PCLK /32 PRESCALER 8-BIT DOWN COUNTER RESET see note (1) CONTROL REGISTER SHADOW REGISTER FOR WDCON WDCON (A7H) PRE2 PRE1 PRE0 - - WDRUN WDTOF WDCLK 002aaa423 (1) Watchdog reset can also be caused by an invalid feed sequence, or by writing to WDCON not immediately followed by a feed sequence. Fig 17. Watchdog timer in Watchdog mode (WDTE = `1'). 8.24 Additional features 8.24.1 Software reset The SRST bit in AUXR1 gives software the opportunity to reset the processor completely, as if an external reset or Watchdog reset had occurred. Care should be taken when writing to AUXR1 to avoid accidental software resets. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 39 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 8.24.2 Dual data pointers The dual Data Pointers (DPTR) provides two different Data Pointers to specify the address used with certain instructions. The DPS bit in the AUXR1 register selects one of the two Data Pointers. Bit 2 of AUXR1 is permanently wired as a logic `0' so that the DPS bit may be toggled (thereby switching Data Pointers) simply by incrementing the AUXR1 register, without the possibility of inadvertently altering other bits in the register. 8.25 Flash program memory 8.25.1 General description The P89LPC906/907/908 Flash memory provides in-circuit electrical erasure and programming. The Flash can be erased, read, and written as bytes. The Sector and Page Erase functions can erase any Flash sector (256 bytes) or page (16 bytes). The Chip Erase operation will erase the entire program memory. In-Circuit Programming using standard commercial programmers is available. In addition, In-Application Programming (IAP) and byte erase allows code memory to be used for non-volatile data storage. On-chip erase and write timing generation contribute to a user-friendly programming interface. The P89LPC906/907/908 Flash reliably stores memory contents even after 100,000 erase and program cycles. The cell is designed to optimize the erase and programming mechanisms. The P89LPC906/907/908 uses VDD as the supply voltage to perform the Program/Erase algorithms. 8.25.2 Features * * * * * * * * 8.25.3 Programming and erase over the full operating voltage range. Byte-erase allowing code memory to be used for data storage. Read/Programming/Erase using ICP. Any flash program/erase operation in 2 ms. Programming with industry-standard commercial programmers. Programmable security for the code in the Flash for each sector. More than 100,000 erase/program cycles for each byte. 10-year minimum data retention. Flash organization The P89LPC906/907/908 program memory consists of four 256 byte sectors. Each sector can be further divided into 16-byte pages. In addition to sector erase, page erase, and byte erase, a 16-byte page register is included which allows from 1 to 16 bytes of a given page to be programmed at the same time, substantially reducing overall programming time. In addition, erasing and reprogramming of user-programmable configuration bytes including UCFG1, the Boot Status Bit, and the Boot Vector is supported. 8.25.4 Flash programming and erasing Different methods of erasing or programming of the Flash are available. The Flash may be programmed or erased in the end-user application (IAP-Lite) under control of the application's firmware. Another option is to use the In-Circuit Programming (ICP) mechanism. This ICP system provides for programming through a serial clock- serial 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 40 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core data interface using a commercially available EPROM programmer which supports this device. This device does not provide for direct verification of code memory contents. Instead this device provides a 32-bit CRC result on either a sector or the entire 1 KB of user code space. 8.25.5 In-circuit programming (ICP) In-Circuit Programming is performed without removing the microcontroller from the system. The In-Circuit Programming facility consists of internal hardware resources to facilitate remote programming of the P89LPC906/907/908 through a two-wire serial interface. The Philips In-Circuit Programming facility has made in-circuit programming in an embedded application, using commercially available programmers, possible with a minimum of additional expense in components and circuit board area. The ICP function uses five pins. Only a small connector (with VDD, VSS, RST, clock, and data signals) needs to be available to interface your application to a commercial programmer in order to use this feature. Additional details may be found in the P89LPC906/907/908 User's Manual. 8.25.6 In-application programming (IAP-Lite) In-Application Programming is performed in the application under the control of the microcontroller's firmware. The IAP-Lite facility consists of internal hardware resources to facilitate programming and erasing. The Philips In-Application Programming Lite has made in-application programming in an embedded application possible without additional components. This is accomplished through the use of four SFRs consisting of a control/status register, a data register, and two address registers. Additional details may be found in the P89LPC906/907/908 User's Manual. 8.25.7 Using flash as data storage The Flash code memory array of this device supports individual byte erasing and programming. Any byte in the code memory array may be read using the MOVC instruction, provided that the sector containing the byte has not been secured (a MOVC instruction is not allowed to read code memory contents of a secured sector). Thus any byte in a non-secured sector may be used for non-volatile data storage. 8.25.8 User configuration bytes Some user-configurable features of the P89LPC906/907/908 must be defined at power-up and therefore cannot be set by the program after start of execution. These features are configured through the use of the Flash byte UCFG1. Please see the P89LPC906/907/908 User's Manual for additional details. 8.25.9 User sector security bytes There are four User Sector Security Bytes, each corresponding to one sector. Please see the P89LPC906/907/908 User's Manual for additional details. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 41 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 9. Limiting values Table 12: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134).[1] Symbol Tamb(bias) Tstg Vxtal Vn IOH(I/O) IOL(I/O) II/O(tot)(max) Ptot(pack) Parameter operating bias ambient temperature storage temperature range voltage on XTAL1, XTAL2 pin to VSS, as applicable voltage on any pin (except XTAL1, XTAL2) to VSS HIGH-level output current per I/O pin LOW-level output current per I/O pin maximum total I/O current total power dissipation per package based on package heat transfer, not device power consumption Conditions Min -55 -65 -0.5 Max +125 +150 VDD + 0.5 +5.5 8 20 120 1.5 Unit C C V V mA mA mA W [1] The following applies to Limiting values: a) Stresses above those listed under Table 12 may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any conditions other than those described in Table 13 "DC electrical characteristics", Table 14 "AC characteristics" and Table 15 "AC characteristics (P89LPC906)" of this specification are not implied. b) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum. c) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless otherwise noted. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 42 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 10. Static characteristics Table 13: DC electrical characteristics VDD = 2.4 V to 3.6 V unless otherwise specified. Tamb = -40 C to +85 C for industrial, unless otherwise specified. Symbol IDD(oper) IDD(idle) IDD(oper) Parameter power supply current, operating (P89LPC906) power supply current, Idle mode (P89LPC906) power supply current, operating (P89LPC907, P89LPC908) power supply current, Idle mode (P89LPC907, P89LPC908) Power supply current, Power-down mode, voltage comparators powered-down Power supply current, Total Power-down mode VDD fall rate Power-on reset detect voltage RAM keep-alive voltage negative-going threshold voltage (Schmitt input) positive-going threshold voltage (Schmitt input) hysteresis voltage LOW-level output voltage; all ports, all modes except Hi-Z IOL = 20 mA IOL = 10 mA IOL = 3.2 mA VOH HIGH-level output voltage, all ports IOH = -8 mA; push-pull mode IOH = -3.2 mA; push-pull mode IOH = -20 A; quasi-bidirectional mode Cig IIL ILI ITL RRST input/output pin capacitance logical 0 input current, all ports logical 1-to-0 transition current, all ports internal reset pull-up resistor VIN = 0.4 V [4] [5] Conditions 3.6 V; 12 MHz 3.6 V; 18 MHz 3.6 V; 12 MHz 3.6 V; 18 MHz 3.6 V; 7.373 MHz [2] [2] [2] [2] [3] Min - Typ[1] 11 14 1 1.5 4 Max 18 23 4 5.6 8 Unit mA mA mA mA mA IDD(idle) 3.6 V; 7.373 MHz [3] - 1 3 mA IDD(PD) 3.6 V [2][3] - - 70 A IDD(TPD) 3.6 V [2][3] 1.5 0.22VDD VDD - 0.1 VDD - 0.7 VDD - 0.3 -30 10 1 0.4VDD 0.6VDD 0.2VDD 0.6 0.3 0.2 VDD - 0.4 VDD - 0.2 - 5 2 50 0.2 0.7VDD 1.0 0.5 0.3 15 -80 10 -450 30 A mV/s mV/s V V V V V V V V V V V pF A A A k (dVDD/dt)r VDD rise rate (dVDD/dt)f VPOR VRAM Vth(HL) Vth(LH) Vhys VOL input leakage current, all ports VIN = VIL or VIH VIN = 2.0 V at VDD = 3.6 V [6] [7][8] 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 43 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core Table 13: DC electrical characteristics...continued VDD = 2.4 V to 3.6 V unless otherwise specified. Tamb = -40 C to +85 C for industrial, unless otherwise specified. Symbol VBO VREF TC(VREF) Parameter brownout trip voltage with BOV = `1', BOPD = `0' bandgap reference voltage bandgap temperature coefficient Conditions 2.4 V < VDD < 3.6 V Min 2.40 1.11 Typ[1] 1.23 10 Max 2.70 1.34 20 Unit V V ppm/ C [1] [2] [3] [4] [5] [6] [7] [8] Typical ratings are not guaranteed. The values listed are at room temperature, 3 V. The IDD(oper), IDD(PD) specifications are measured using an external clock with the following functions disabled: comparators, brownout detect, and watchdog timer (P89LPC906). The IDD(oper), IDD(PD) specifications are measured with the following functions disabled: comparators, brownout detect, and watchdog timer (P89LPC907, P89LPC908). Pin capacitance is characterized but not tested. Measured with port in quasi-bidirectional mode. Measured with port in high-impedance mode. Ports in quasi-bidirectional mode with weak pull-up (applies to all port pins with pull-ups) Port pins source a transition current when used in quasi-bidirectional mode and externally driven from `1' to `0'. This current is highest when VIN is approximately 2 V. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 44 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 11. Dynamic characteristics Table 14: AC characteristics VDD = 2.4 V to 3.6 V, unless otherwise specified. Tamb = -40 C to +85 C for industrial, unless otherwise specified.[1] Symbol fRCOSC Parameter internal RC oscillator frequency (nominal f = 7.3728 MHz) trimmed to 1 % at Tamb = 25 C internal Watchdog oscillator frequency (nominal f = 400 kHz) oscillator frequency clock cycle CLKLP active frequency glitch rejection, P1.5/RST pin signal acceptance, P1.5/RST pin glitch rejection, any pin except P1.5/RST signal acceptance, any pin except P1.5/RST External clock (P89LPC906) tCHCX tCLCX tCLCH tCHCL tXLXL tQVXH tXHQX tXHDX tDVXH [1] Conditions Variable clock Min 7.189 Max 7.557 fosc = 12 MHz Min 7.189 Max 7.557 Unit MHz fWDOSC 320 520 320 520 kHz Crystal oscillator (P89LPC906) fosc tCLCL fCLKP Glitch filter 125 50 50 15 125 50 50 15 ns ns ns ns 0 see Figure 19 83 0 12 8 MHz ns MHz HIGH time LOW time rise time fall time serial port clock cycle time output data set-up to clock rising edge output data hold after clock rising edge input data hold after clock rising edge see Figure 19 see Figure 19 see Figure 19 see Figure 19 see Figure 18 see Figure 18 see Figure 18 see Figure 18 33 33 16 tCLCL 13 tCLCL 150 tCLCL - tCLCX tCLCL - tCHCX 8 8 tCLCL + 20 0 - 33 33 1333 1083 150 8 8 103 0 - ns ns ns ns ns ns ns ns ns Shift register (UART mode 0 - P89LPC908) input data valid to clock rising edge see Figure 18 Parameters are valid over operating temperature range unless otherwise specified. Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 45 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core Table 15: AC characteristics (P89LPC906) VDD = 3.0 V to 3.6 V, unless otherwise specified. Tamb = -40 C to +85 C for industrial, unless otherwise specified.[1] Symbol fRCOSC Parameter internal RC oscillator frequency (nominal f = 7.3728 MHz) trimmed to 1 % at Tamb = 25 C internal Watchdog oscillator frequency (nominal f = 400 kHz) oscillator frequency clock cycle CLKLP active frequency glitch rejection, P1.5/RST pin signal acceptance, P1.5/RST pin glitch rejection, any pin except P1.5/RST signal acceptance, any pin except P1.5/RST External clock tCHCX tCLCX tCLCH tCHCL [1] [2] [2] Conditions Variable clock Min 7.189 Max 7.557 fosc = 18 MHz Min 7.189 Max 7.557 Unit MHz fWDOSC 320 520 320 520 kHz Crystal oscillator fosc tCLCL fCLKP Glitch filter 125 50 50 15 125 50 50 15 ns ns ns ns 0 83 0 12 8 MHz ns MHz see Figure 19 HIGH time LOW time rise time fall time see Figure 19 see Figure 19 see Figure 19 see Figure 19 22 22 - tCLCL - tCLCX tCLCL - tCHCX 5 5 22 22 - 5 5 ns ns ns ns Parameters are valid over operating temperature range unless otherwise specified. Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz. When using an oscillator frequency above 12 MHz, the reset input function of P1.5 must be enabled. An external circuit is required to hold the device in reset at power-up until VDD has reached its specified level. When system power is removed VDD will fall below the minimum specified operating voltage. When using an oscillator frequency above 12 MHz, in some applications, an external brownout detect circuit may be required to hold the device in reset when VDD falls below the minimum specified operating voltage. tXLXL Clock tQVXH Output Data 0 Write to SBUF Input Data Clear RI Set RI 002aaa425 tXHQX 1 tXHDX Set TI Valid Valid Valid Valid Valid Valid Valid Valid 2 3 4 5 6 7 tXHDV Fig 18. Shift register mode timing. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 46 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core VDD - 0.5 V 0.45 V 0.2 VDD + 0.9 0.2 VDD - 0.1 V tCHCX tCHCL tCLCX tC tCLCH 002aaa416 Fig 19. External clock timing. 12. Comparator electrical characteristics Table 16: Comparator electrical characteristics VDD = 2.4 V to 3.6 V, unless otherwise specified. Tamb = -40 C to +85 C for industrial, unless otherwise specified. Symbol VIO VCR CMRR Parameter offset voltage comparator inputs common mode range comparator inputs common mode rejection ratio response time comparator enable to output valid IIL [1] [1] Conditions Min 0 - Typ 250 - Max 20 VDD - 0.3 -50 500 10 10 Unit mV V dB ns s A input leakage current, comparator 0 < VIN < VDD - This parameter is characterized, but not tested in production. 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 47 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 13. Package outline SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 D E A X c y HE vMA Z 8 5 Q A2 A1 pin 1 index Lp 1 e bp 4 wM L detail X (A 3) A 0 2.5 scale 5 mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 1.75 0.069 A1 0.25 0.10 A2 1.45 1.25 A3 0.25 0.01 bp 0.49 0.36 c 0.25 0.19 D (1) 5.0 4.8 0.20 0.19 E (2) 4.0 3.8 0.16 0.15 e 1.27 0.05 HE 6.2 5.8 L 1.05 Lp 1.0 0.4 Q 0.7 0.6 v 0.25 0.01 w 0.25 0.01 y 0.1 0.004 Z (1) 0.7 0.3 0.028 0.012 0.010 0.057 0.004 0.049 0.019 0.0100 0.014 0.0075 0.244 0.039 0.028 0.041 0.228 0.016 0.024 8o o 0 Notes 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. OUTLINE VERSION SOT96-1 REFERENCES IEC 076E03 JEDEC MS-012 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Fig 20. SOT96-1 (SO8). 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 48 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 14. Revision history Table 17: Rev Date 05 20041217 Revision history CPCN Description Product data (9397 750 14467) Modification: * 04 03 02 01 20031121 20030929 20030801 20030602 - Added 18 MHz information. Product data (9397 750 12289); ECN 853-2435 01-A14556 of 18 November 2003 Product data (9397 750 12032); ECN 853-2435 30349 of 11 September 2003 Product data (9397 750 11787); ECN 853-2435 30153 of 28 July 2003 Preliminary data (9397 750 11524) 9397 750 14467 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 49 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core 15. Data sheet status Level I II Data sheet status[1] Objective data Preliminary data Product status[2][3] Development Qualification Definition This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). III Product data Production [1] [2] [3] Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 16. Definitions Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 17. Disclaimers Life support -- These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Contact information For additional information, please visit http://www.semiconductors.philips.com. For sales office addresses, send e-mail to: sales.addresses@www.semiconductors.philips.com. 9397 750 14467 Fax: +31 40 27 24825 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data Rev. 05 -- 17 December 2004 50 of 51 Philips Semiconductors P89LPC906/907/908 8-bit microcontrollers with two-clock 80C51 core Contents 1 2 2.1 2.2 3 3.1 4 5 5.1 5.2 6 7 8 8.1 8.2 8.2.1 8.2.2 8.2.3 8.2.4 8.2.5 8.2.6 8.3 8.4 8.5 8.6 8.7 8.8 8.9 8.9.1 8.10 8.10.1 8.11 8.11.1 8.11.2 8.11.3 8.11.4 8.11.5 8.11.6 8.11.7 8.12 8.12.1 8.12.2 8.13 8.13.1 8.13.2 8.13.3 8.14 8.15 8.15.1 8.15.2 8.15.3 8.15.4 8.15.5 General description . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Principal features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Additional features . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pinning information. . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Logic symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Special function registers. . . . . . . . . . . . . . . . . . . . . 14 Functional description . . . . . . . . . . . . . . . . . . . . . . . 24 Enhanced CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Clock definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 CPU clock (OSCCLK) . . . . . . . . . . . . . . . . . . . . . . . 24 Low speed oscillator option (P89LPC906) . . . . . . . . 24 Medium speed oscillator option (P89LPC906). . . . . 24 High speed oscillator option (P89LPC906) . . . . . . . 24 Clock output (P89LPC906) . . . . . . . . . . . . . . . . . . . 25 On-chip RC oscillator option . . . . . . . . . . . . . . . . . . 25 Watchdog oscillator option . . . . . . . . . . . . . . . . . . . . 25 External clock input option (P89LPC906) . . . . . . . . 25 CPU CLock (CCLK) wake-up delay . . . . . . . . . . . . . 27 CPU CLOCK (CCLK) modification: DIVM register . . 27 Low power select . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Memory organization . . . . . . . . . . . . . . . . . . . . . . . . 27 Data RAM arrangement . . . . . . . . . . . . . . . . . . . . . . 27 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 External interrupt inputs . . . . . . . . . . . . . . . . . . . . . . 28 I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Port configurations . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Quasi-bidirectional output configuration. . . . . . . . . . 31 Open-drain output configuration. . . . . . . . . . . . . . . . 31 Input-only configuration . . . . . . . . . . . . . . . . . . . . . . 31 Push-pull output configuration . . . . . . . . . . . . . . . . . 31 Port 0 analog functions . . . . . . . . . . . . . . . . . . . . . . 31 Additional port features . . . . . . . . . . . . . . . . . . . . . . 32 Power monitoring functions . . . . . . . . . . . . . . . . . . . 32 Brownout detection . . . . . . . . . . . . . . . . . . . . . . . . . 32 Power-on detection . . . . . . . . . . . . . . . . . . . . . . . . . 32 Power reduction modes . . . . . . . . . . . . . . . . . . . . . . 32 Idle mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Power-down mode . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Total Power-down mode . . . . . . . . . . . . . . . . . . . . . . 33 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Timers/counters 0 and 1 . . . . . . . . . . . . . . . . . . . . . 34 Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Mode 6 (P89LPC907) . . . . . . . . . . . . . . . . . . . . . . . 34 Timer overflow toggle output (P89LPC907) . . . . . . . 35 Real-Time clock/system timer. . . . . . . . . . . . . . . . . . 35 UART (P89LPC908) . . . . . . . . . . . . . . . . . . . . . . . . . 35 Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Baud rate generator and selection . . . . . . . . . . . . . . 36 Framing error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Break detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Double buffering . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Transmit interrupts with double buffering enabled (Modes 1, 2 and 3) . . . . . . . . . . . . . . . . . . . 37 8.17.10 The 9th bit (bit 8) in double buffering (Modes 1, 2 and 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 8.18 Analog comparator . . . . . . . . . . . . . . . . . . . . . . . . . . 37 8.19 Internal reference voltage . . . . . . . . . . . . . . . . . . . . . 37 8.20 Comparator interrupt. . . . . . . . . . . . . . . . . . . . . . . . . 37 8.21 Comparator and power reduction modes . . . . . . . . . 38 8.22 Keypad interrupt (KBI) . . . . . . . . . . . . . . . . . . . . . . . 38 8.23 Watchdog timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 8.24 Additional features . . . . . . . . . . . . . . . . . . . . . . . . . . 39 8.24.1 Software reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 8.24.2 Dual data pointers. . . . . . . . . . . . . . . . . . . . . . . . . . . 40 8.25 Flash program memory. . . . . . . . . . . . . . . . . . . . . . . 40 8.25.1 General description. . . . . . . . . . . . . . . . . . . . . . . . . . 40 8.25.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 8.25.3 Flash organization . . . . . . . . . . . . . . . . . . . . . . . . . . 40 8.25.4 Flash programming and erasing . . . . . . . . . . . . . . . . 40 8.25.5 In-circuit programming (ICP). . . . . . . . . . . . . . . . . . . 41 8.25.6 In-application programming (IAP-Lite) . . . . . . . . . . . 41 8.25.7 Using flash as data storage . . . . . . . . . . . . . . . . . . . 41 8.25.8 User configuration bytes . . . . . . . . . . . . . . . . . . . . . . 41 8.25.9 User sector security bytes . . . . . . . . . . . . . . . . . . . . 41 9 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 10 Static characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 43 11 Dynamic characteristics . . . . . . . . . . . . . . . . . . . . . . 45 12 Comparator electrical characteristics . . . . . . . . . . . 47 13 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 14 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 15 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 16 Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 17 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 8.15.6 8.16 8.17 8.17.1 8.17.2 8.17.3 8.17.4 8.17.5 8.17.6 8.17.7 8.17.8 8.17.9 (c) Koninklijke Philips Electronics N.V. 2004. Printed in the U.S.A. All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 17 December 2004 Document order number: 9397 750 14467 |
Price & Availability of P89LPC906
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |